View LTC2436-1_294236.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

LTC2436-1 2-Channel Differential Input 16-Bit No Latency ADC
FEATURES
s s s
DESCRIPTIO
s s s s
s
s s s s
2-Channel Differential Input with Automatic Channel Selection (Ping-Pong) Low Supply Current: 200A, 4A in Autosleep Differential Input and Differential Reference with GND to VCC Common Mode Range 0.12LSB INL, No Missing Codes 0.16LSB Full-Scale Error and 0.006LSB Offset 800nV RMS Noise, Independent of VREF No Latency: Digital Filter Settles in a Single Cycle and Each Channel Conversion is Accurate Internal Oscillator--No External Components Required 87dB Min, 50Hz and 60Hz Notch Filter Narrow SSOP-16 Package Single Supply 2.7V to 5.5V Operation Pin Compatible with the 24-Bit LTC2412
The LTC(R)2436-1 is a 2-channel differential input micropower 16-bit No Latency TM analog-to-digital converter with an integrated oscillator. It provides 0.5LSB INL and 800nV RMS noise independent of VREF. The two differential channels convert alternately with a channel identification included in the conversion result. It uses delta-sigma technology and provides single conversion settling of the digital filter. Through a single pin, the LTC2436-1 can be configured for better than 87dB input differential mode rejection at 50Hz and 60Hz 2%, or it can be driven by an external oscillator for a user defined rejection frequency. The internal oscillator requires no external frequency setting components. The converter accepts any external differential reference voltage from 0.1V to VCC for flexible ratiometric and remote sensing measurement configurations. The fullscale differential input range is from - 0.5 * VREF to 0.5 * VREF. The reference common mode voltage, VREFCM, and the input common mode voltage, VINCM, may be independently set anywhere between GND and VCC. The DC common mode input rejection is better than 140dB. The LTC2436-1 communicates through a flexible 3-wire digital interface which is compatible with SPI and MICROWIRETM protocols.
, LTC and LT are registered trademarks of Linear Technology Corporation. No Latency is a trademark of Linear Technology Corporation. MICROWIRE is a trademark of National Semiconductor Corporation.
APPLICATIO S
s s s s s s s s
Direct Sensor Digitizer Weight Scales Direct Temperature Measurement Gas Analyzers Strain-Gage Transducers Instrumentation Data Acquisition Industrial Process Control
TYPICAL APPLICATIO
5V REF 1F 4.9k (100mV) 100 1 2 4 VCC
+
EFFECTIVE RESOLUTION (V)*
FO
14
REF CH0+ LTC2436-1 CH0- REF - CH1
+
= EXTERNAL CLOCK SOURCE = INTERNAL OSC/SIMULTANEOUS 50Hz/60Hz REJECTION
50 40 30 20 10 0 0 5 4 3 2 VREF (V) 24361 TA02 *COMBINES EFFECTS OF PEAK-TO-PEAK NOISE AND 16-BIT STEP SIZE (VREF/216) 1
5 THERMOCOUPLE 3 6 7 8, 9, 10, 15, 16
SCK SDO CS
13 12 11 3-WIRE SPI INTERFACE
CH1- GND
24361 TA01
U
Effective Resolution vs VREF
90 80 70 60
U
U
24361f
1
LTC2436-1
ABSOLUTE
(Notes 1, 2)
AXI U
RATI GS
PACKAGE/ORDER I FOR ATIO
TOP VIEW VCC REF + REF - CH0+ CH0- CH1+ CH1- GND 1 2 3 4 5 6 7 8 16 GND 15 GND 14 FO 13 SCK 12 SDO 11 CS 10 GND 9 GND
Supply Voltage (VCC) to GND .......................- 0.3V to 7V Analog Input Voltage to GND .................................... - 0.3V to (VCC + 0.3V) Reference Input Voltage to GND .................................... - 0.3V to (VCC + 0.3V) Digital Input Voltage to GND ........ - 0.3V to (VCC + 0.3V) Digital Output Voltage to GND ..... - 0.3V to (VCC + 0.3V) Operating Temperature Range LTC2436-1C ............................................ 0C to 70C LTC2436-1I ........................................ - 40C to 85C Storage Temperature Range ................. - 65C to 150C Lead Temperature (Soldering, 10 sec).................. 300C
ORDER PART NUMBER LTC2436-1CGN LTC2436-1IGN
GN PART MARKING 24361 24361I
GN PACKAGE 16-LEAD PLASTIC SSOP TJMAX = 125C, JA = 110C/W
Consult LTC Marketing for parts specified with wider operating temperature ranges.
ELECTRICAL CHARACTERISTICS
PARAMETER Resolution (No Missing Codes) Integral Nonlinearity CONDITIONS
The q denotes specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Notes 3, 4)
MIN
q
TYP 0.06 0.12 0.30 0.006 10
MAX
UNITS Bits LSB LSB LSB LSB nV/C
0.1V VREF VCC, -0.5 * VREF VIN 0.5 * VREF, (Note 5)
16 3 1
5V VCC 5.5V, REF+ = 2.5V, REF- = GND, VINCM = 1.25V, (Note 6) q 5V VCC 5.5V, REF+ = 5V, REF- = GND, VINCM = 2.5V, (Note 6) REF+ = 2.5V, REF- = GND, VINCM = 1.25V, (Note 6) 2.5V REF+ VCC, REF- = GND, GND IN+ = IN- VCC, (Note 13) 2.5V REF+ VCC, REF- = GND, GND IN+ = IN- VCC 2.5V REF+ VCC, REF- = GND, IN+ = 0.75REF+, IN- = 0.25 * REF+ 2.5V REF+ VCC, REF- = GND, IN+ = 0.75REF+, IN- = 0.25 * REF+ 2.5V REF+ VCC, REF- = GND, IN+ = 0.25 * REF+, IN- = 0.75 * REF+ 2.5V REF+ VCC, REF- = GND, IN+ = 0.25 * REF+, IN- = 0.75 * REF+ 5V VCC 5.5V, REF+ = 2.5V, REF- = GND, VINCM = 1.25V 5V VCC 5.5V, REF+ = 5V, REF- = GND, VINCM = 2.5V REF+ = 2.5V, REF- = GND, VINCM = 1.25V, (Note 6) 5V VCC 5.5V, REF+ = 5V, REF - = GND, GND IN- = IN+ VCC, (Note 13)
q q q
Offset Error Offset Error Drift Positive Full-Scale Error Positive Full-Scale Error Drift Negative Full-Scale Error Negative Full-Scale Error Drift Total Unadjusted Error
0.16 0.03 0.16 0.03 0.20 0.20 0.25 0.8
3
ppm of VREF/C 3 LSB ppm of VREF/C 3 3 3 LSB LSB LSB VRMS
Output Noise
2
U
LSB
24361f
W
U
U
WW
W
LTC2436-1
CO VERTER CHARACTERISTICS
PARAMETER Input Common Mode Rejection DC Input Common Mode Rejection 49Hz to 61.2Hz Input Normal Mode Rejection 49Hz to 61.2Hz Reference Common Mode Rejection DC Power Supply Rejection, DC Power Supply Rejection, Simultaneous 50Hz/60Hz 2% CONDITIONS
The q denotes specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Notes 3, 4)
MIN
q q q q
A ALOG I PUT A D REFERE CE
SYMBOL IN+ IN- VIN REF+ REF- VREF CS (IN+) CS CS (IN-) (REF+) (IN+) (IN-) (REF-) PARAMETER Absolute/Common Mode IN+ Voltage Absolute/Common Mode IN- Voltage Input Differential Voltage Range (IN+ - IN-) Absolute/Common Mode REF+ Voltage Absolute/Common Mode REF- Voltage Reference Differential Voltage Range (REF+ - REF-) IN+ Sampling Capacitance IN- Sampling Capacitance REF+ Sampling Capacitance REF- Sampling Capacitance IN+ IN- DC Leakage Current DC Leakage Current
The q denotes specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 3)
CONDITIONS
q q q q q q
CS (REF-) IDC_LEAK IDC_LEAK IDC_LEAK
IDC_LEAK (REF+)
REF+ DC Leakage Current REF- DC Leakage Current
U
U
U
U
TYP 140
MAX
UNITS dB dB dB
2.5V REF+ VCC, REF- = GND, GND IN- = IN+ VCC (Note 5) 2.5V REF+ VCC, REF- = GND, GND IN - = IN+ VCC, (Notes 5, 7) (Note 5, 7) 2.5V REF+ VCC, GND REF- 2.5V, VREF = 2.5V, IN- = IN+ = GND (Note 5) REF+ = 2.5V, REF- = GND, IN- = IN+ = GND REF+ = 2.5V, REF- = GND, IN- = IN+ = GND, (Note 7)
130 140 87 130
140 120 120
dB dB dB
U
MIN GND - 0.3 GND - 0.3 -VREF/2 0.1 GND 0.1
TYP
MAX VCC + 0.3 VCC + 0.3 VREF/2 VCC VCC - 0.1 VCC
UNITS V V V V V V pF pF pF pF
18 18 18 18 CS = VCC CS = VCC CS = VCC = 5V, IN+ = GND = 5V, IN - = 5.5V = 5V, REF - = GND
q q q q
-10 -10 -10 -10
1 1 1 1
10 10 10 10
nA nA nA nA
CS = VCC = 5V, REF+ = 5.5V
24361f
3
LTC2436-1 DIGITAL I PUTS A D DIGITAL OUTPUTS
SYMBOL VIH VIL VIH VIL IIN IIN CIN CIN VOH VOL VOH VOL IOZ PARAMETER High Level Input Voltage CS, FO Low Level Input Voltage CS, FO High Level Input Voltage SCK Low Level Input Voltage SCK Digital Input Current CS, FO Digital Input Current SCK Digital Input Capacitance CS, FO Digital Input Capacitance SCK High Level Output Voltage SDO Low Level Output Voltage SDO High Level Output Voltage SCK Low Level Output Voltage SCK Hi-Z Output Leakage SDO (Note 8) IO = -800A IO = 1.6mA IO = -800A (Note 9) IO = 1.6mA (Note 9)
q q q q q
The q denotes specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 3)
CONDITIONS 2.7V VCC 5.5V 2.7V VCC 3.3V 4.5V VCC 5.5V 2.7V VCC 5.5V 2.7V VCC 5.5V (Note 8) 2.7V VCC 3.3V (Note 8) 4.5V VCC 5.5V (Note 8) 2.7V VCC 5.5V (Note 8) 0V VIN VCC 0V VIN VCC (Note 8)
q q q q q q
POWER REQUIRE E TS
SYMBOL VCC ICC PARAMETER Supply Voltage Supply Current Conversion Mode Sleep Mode Sleep Mode
The q denotes specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 3)
CONDITIONS
q
4
UW
U
U
MIN 2.5 2.0
TYP
MAX
UNITS V V
0.8 0.6 2.5 2.0 0.8 0.6 -10 -10 10 10 VCC - 0.5 0.4 VCC - 0.5 0.4 -10 10 10 10
V V V V V V A A pF pF V V V V A
MIN 2.7
TYP
MAX 5.5
UNITS V A A A
CS = 0V (Note 14) CS = VCC (Notes 11, 14) CS = VCC, 2.7V VCC 3.3V (Notes 11, 14)
q q
200 4 2
300 13
24361f
LTC2436-1 TI I G CHARACTERISTICS
SYMBOL fEOSC tHEO tLEO tCONV fISCK DISCK fESCK tLESCK tHESCK tDOUT_ISCK tDOUT_ESCK t1 t2 t3 t4 tKQMAX tKQMIN t5 t6 PARAMETER External Oscillator Frequency Range External Oscillator High Period External Oscillator Low Period Conversion Time Internal SCK Frequency Internal SCK Duty Cycle External SCK Frequency Range External SCK Low Period External SCK High Period Internal SCK 19-Bit Data Output Time External SCK 19-Bit Data Output Time CS to SDO Low Z CS to SDO High Z CS to SCK CS to SCK SCK to SDO Valid SDO Hold After SCK SCK Set-Up Before CS SCK Hold After CS (Note 5) (Note 9) (Note 8) FO = 0V External Oscillator (Note 10) Internal Oscillator (Note 9) External Oscillator (Notes 9, 10) (Note 9) (Note 8) (Note 8) (Note 8) Internal Oscillator (Notes 9, 11) External Oscillator (Notes 9, 10) (Note 8)
q q q q q q q q q q q q q q q
The q denotes specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 3)
CONDITIONS
q q q q q
Note 1: Absolute Maximum Ratings are those values beyond which the life of the device may be impaired. Note 2: All voltage values are with respect to GND. Note 3: VCC = 2.7V to 5.5V unless otherwise specified. VREF = REF + - REF -, VREFCM = (REF + + REF -)/2; VIN = IN+ - IN -, VINCM = (IN + + IN -)/2, IN+ and IN- are defined as the selected positive (CH0+ or CH1+) and negative (CH0- or CH1-) input respectively. Note 4: FO pin tied to GND or to an external conversion clock source with fEOSC = 139,800Hz unless otherwise specified. Note 5: Guaranteed by design, not subject to test. Note 6: Integral nonlinearity is defined as the deviation of a code from a precise analog input voltage. Maximum specifications are limited by the LSB step size (VREF/216) and the single shot measurement. Typical specifications are measured from the center of the quantization band. Note 7: FO = GND (internal oscillator) or fEOSC = 139,800Hz 2% (external oscillator).
UW
MIN 2.56 0.25 0.25 143.8
TYP
MAX 2000 390 390
UNITS kHz s s ms ms kHz kHz
146.7 149.6 20510/fEOSC (in kHz) 17.5 fEOSC/8
45 250 250 1.06
55 2000
% kHz ns ns
1.09 1.11 152/fEOSC (in kHz) 19/fESCK (in kHz) 200 200 200 220
ms ms ms ns ns ns ns ns ns ns
0 0 0 50 15 50
50
ns
Note 8: The converter is in external SCK mode of operation such that the SCK pin is used as digital input. The frequency of the clock signal driving SCK during the data output is fESCK and is expressed in kHz. Note 9: The converter is in internal SCK mode of operation such that the SCK pin is used as digital output. In this mode of operation the SCK pin has a total equivalent load capacitance CLOAD = 20pF. Note 10: The external oscillator is connected to the FO pin. The external oscillator frequency, fEOSC, is expressed in kHz. Note 11: The converter uses the internal oscillator. FO = 0V. Note 12: 800nV RMS noise is independent of VREF. Since the noise performance is limited by the quantization, lowering VREF improves the effective resolution. Note 13: Guaranteed by design and test correlation. Note 14: The low sleep mode current is valid only when CS is high.
24361f
5
LTC2436-1
PI FU CTIO S
VCC (Pin 1): Positive Supply Voltage. Bypass to GND with a 10F tantalum capacitor in parallel with 0.1F ceramic capacitor as close to the part as possible. REF + (Pin 2), REF - (Pin 3): Differential Reference Input. The voltage on these pins can have any value between GND and VCC as long as the reference positive input, REF +, is maintained more positive than the reference negative input, REF -, by at least 0.1V. CH0+ (Pin 4): Positive Input for Differential Channel 0. CH0 - (Pin 5): Negative Input for Differential Channel 0. CH1+ (Pin 6): Positive Input for Differential Channel 1. CH1- (Pin 7): Negative Input for Differential Channel 1. The voltage on these four analog inputs (Pins 4 to 7) can have any value between GND and VCC. Within these limits the converter bipolar input range (VIN = IN+ - IN-) extends from - 0.5 * (VREF ) to 0.5 * (VREF ). Outside this input range the converter produces unique overrange and underrange output codes. GND (Pins 8, 9, 10, 15, 16): Ground. Multiple ground pins internally connected for optimum ground current flow and VCC decoupling. Connect each one of these pins to a ground plane through a low impedance connection. All five pins must be connected to ground for proper operation. CS (Pin 11): Active LOW Digital Input. A LOW on this pin enables the SDO digital output and wakes up the ADC. Following each conversion the ADC automatically enters the Sleep mode and remains in this low power state as long as CS is HIGH. A LOW-to-HIGH transition on CS during the Data Output transfer aborts the data transfer and starts a new conversion. SDO (Pin 12): Three-State Digital Output. During the Data Output period, this pin is used as serial data output. When the chip select CS is HIGH (CS = VCC) the SDO pin is in a high impedance state. During the Conversion and Sleep periods, this pin is used as the conversion status output. The conversion status can be observed by pulling CS LOW. SCK (Pin 13): Bidirectional Digital Clock Pin. In Internal Serial Clock Operation mode, SCK is used as digital output for the internal serial interface clock during the Data Output period. In External Serial Clock Operation mode, SCK is used as digital input for the external serial interface clock during the Data Output period. A weak internal pullup is automatically activated in Internal Serial Clock Operation mode. The Serial Clock Operation mode is determined by the logic level applied to the SCK pin at power up or during the most recent falling edge of CS. FO (Pin 14): Frequency Control Pin. Digital input that controls the ADC's notch frequencies and conversion time. When the FO pin is connected to GND (FO = 0V), the converter uses its internal oscillator and rejects 50Hz and 60Hz simultaneously. When FO is driven by an external clock signal with a frequency fEOSC, the converter uses this signal as its system clock and the digital filter has 87dB minimum rejection in the range fEOSC/2560 14% and 110dB minimum rejection at fEOSC/2560 4%.
6
U
U
U
24361f
LTC2436-1
FU CTIO AL BLOCK DIAGRA
VCC GND
CH0+ CH0- MUX CH1+ CH1-
IN + DIFFERENTIAL 3RD ORDER MODULATOR SERIAL INTERFACE DECIMATING FIR
IN -
+
REF + REF -
24361 FD
Figure 1. Functional Block Diagram
TEST CIRCUITS
VCC 1.69k
SDO 1.69k CLOAD = 20pF
Hi-Z TO VOH VOL TO VOH VOH TO Hi-Z
24361 TA03
W
INTERNAL OSCILLATOR AUTOCALIBRATION AND CONTROL FO (INT/EXT) SCK SDO CS
U
U
-
CH0/CH1 PING-PONG
SDO CLOAD = 20pF
Hi-Z TO VOL VOH TO VOL VOL TO Hi-Z
24361 TA04
24361f
7
LTC2436-1
APPLICATIO S I FOR ATIO
CONVERTER OPERATION Converter Operation Cycle
The LTC2436-1 is a low power, ADC with automatic alternate channel selection between the two differential channels and an easy-to-use 3-wire serial interface (see Figure 1). Channel 0 is selected automatically at power up and the two channels are selected alternately afterwards (ping-pong). Its operation is made up of three states. The converter operating cycle begins with the conversion, followed by the low power sleep state and ends with the data output (see Figure 2). The 3-wire interface consists of serial data output (SDO), serial clock (SCK) and chip select (CS). Initially, the LTC2436-1 performs a conversion. Once the conversion is complete, the device enters the sleep state. The part remains in the sleep state as long as CS is HIGH. While in this sleep state, power consumption is reduced by nearly two orders of magnitude. The conversion result is held indefinitely in a static shift register while the converter is in the sleep state. Once CS is pulled LOW, the device exits the low power mode and enters the data output state. If CS is pulled HIGH before the first rising edge of SCK, the device returns to the low power sleep mode and the conversion result is still held in the internal static shift register. If CS remains LOW
POWER UP IN+ = CH0 +, IN - = CH0 -
CONVERT
SLEEP
FALSE
CS = LOW AND SCK TRUE
DATA OUTPUT SWITCH CHANNEL
24361 F02
Figure 2. LTC2436-1 State Transition Diagram
8
U
after the first rising edge of SCK, the device begins outputting the conversion result. Taking CS high at this point will terminate the data output state and start a new conversion. There is no latency in the conversion result. The data output corresponds to the conversion just performed. This result is shifted out on the serial data out pin (SDO) under the control of the serial clock (SCK). Data is updated on the falling edge of SCK allowing the user to reliably latch data on the rising edge of SCK (see Figure 3). The data output state is concluded once 19 bits are read out of the ADC or when CS is brought HIGH. The device automatically initiates a new conversion and the cycle repeats. In order to maintain compatibility with 24-/32-bit data transfers, it is possible to clock the LTC2436-1 with additional serial clock pulses. This results in additional data bits which are always logic HIGH. Through timing control of the CS and SCK pins, the LTC2436-1 offers several flexible modes of operation (internal or external SCK and free-running conversion modes). These various modes do not require programming configuration registers; moreover, they do not disturb the cyclic operation described above. These modes of operation are described in detail in the Serial Interface Timing Modes section. Conversion Clock A major advantage the delta-sigma converter offers over conventional type converters is an on-chip digital filter (commonly implemented as a Sinc or Comb filter). For high resolution, low frequency applications, this filter is typically designed to reject line frequencies of 50Hz and 60Hz plus their harmonics. The filter rejection performance is directly related to the accuracy of the converter system clock. The LTC2436-1 incorporates a highly accurate on-chip oscillator. This eliminates the need for external frequency setting components such as crystals or oscillators. Clocked by the on-chip oscillator, the LTC2436-1 achieves a minimum of 87dB rejection over the range 49Hz to 61.2Hz. Ease of Use The LTC2436-1 data output has no latency, filter settling delay or redundant data associated with the conversion
24361f
W
UU
LTC2436-1
APPLICATIO S I FOR ATIO
cycle. There is a one-to-one correspondence between the conversion and the output data. Therefore, multiplexing multiple analog voltages is easy. The LTC2436-1 performs offset and full-scale calibrations every conversion cycle. This calibration is transparent to the user and has no effect on the cyclic operation described above. The advantage of continuous calibration is extreme stability of offset and full-scale readings with respect to time, supply voltage change and temperature drift. Power-Up Sequence The LTC2436-1 automatically enters an internal reset state when the power supply voltage VCC drops below approximately 2V. This feature guarantees the integrity of the conversion result and of the serial interface mode selection. (See the 2-wire I/O sections in the Serial Interface Timing Modes section.) When the VCC voltage rises above this critical threshold, the converter creates an internal power-on-reset (POR) signal with a typical duration of 1ms. The POR signal clears all internal registers and selects channel 0. Following the POR signal, the LTC2436-1 starts a normal conversion cycle and follows the succession of states described above. The first conversion result following POR is accurate within the specifications of the device if the power supply voltage is restored within the operating range (2.7V to 5.5V) before the end of the POR time interval. Reference Voltage Range This converter accepts a truly differential external reference voltage. The absolute/common mode voltage specification for the REF + and REF - pins covers the entire range from GND to VCC. For correct converter operation, the REF + pin must always be more positive than the REF - pin. The LTC2436-1 can accept a differential reference voltage from 0.1V to VCC. The converter output noise is determined by the thermal noise of the front-end circuits, and as such, its value in nanovolts is nearly constant with reference voltage. A decrease in reference voltage will significantly improve the converter's effective resolution, since the thermal noise (800nV) is well below the quantization level of the device (75.6V for a 5V reference). At the minimum reference (100mV) the thermal noise
U
remains constant at 800nV RMS (or 4.8VP-P), while the quantization is reduced to 1.5V per LSB. As a result, lower the reference improves the effective resolution for low level input voltages. Input Voltage Range The analog input is truly differential with an absolute/ common mode range for the CH0+/CH0- or CH1+/CH1- input pins extending from GND - 0.3V to VCC + 0.3V. Outside these limits, the ESD protection devices begin to turn on and the errors due to input leakage current increase rapidly. Within these limits, the LTC2436-1 converts the bipolar differential input signal, VIN = IN+ - IN-, from - FS = - 0.5 * VREF to +FS = 0.5 * VREF where VREF = REF+ - REF-, with the selected channel referred as IN+ and IN-. Outside this range, the converter indicates the overrange or the underrange condition using distinct output codes. Input signals applied to the analog input pins may extend by 300mV below ground and above VCC. In order to limit any fault current, resistors of up to 5k may be added in series with the pins without affecting the performance of the device. In the physical layout, it is important to maintain the parasitic capacitance of the connection between these series resistors and the corresponding pins as low as possible; therefore, the resistors should be located as close as practical to the pins. The effect of the series resistance on the converter accuracy can be evaluated from the curves presented in the Input Current/Reference Current sections. In addition, series resistors will introduce a temperature dependent offset error due to the input leakage current. A 10nA input leakage current will develop a 1LSB offset error on an 8k resistor if VREF = 5V. This error has a very strong temperature dependency. Output Data Format The LTC2436-1 serial output data stream is 19 bits long. The first 3 bits represent status information indicating the conversion state, selected channel and sign. The next 16 bits are the conversion result, MSB first. The third and fourth bit together are also used to indicate an underrange condition (the differential input voltage is below -FS) or an overrange condition (the differential input voltage is above +FS). 24361f
W
UU
9
LTC2436-1
APPLICATIO S I FOR ATIO
Bit 18 (first output bit) is the end of conversion (EOC) indicator. This bit is available at the SDO pin during the conversion and sleep states whenever the CS pin is LOW. This bit is HIGH during the conversion and goes LOW when the conversion is complete. Bit 17 (second output bit) is the selected channel indicator. The bit is LOW for channel 0 and HIGH for channel 1 selected. Bit 16 (third output bit) is the conversion result sign indicator (SIG). If VIN is >0, this bit is HIGH. If VIN is <0, this bit is LOW. Bit 15 (fourth output bit) is the most significant bit (MSB) of the result. This bit in conjunction with Bit 16 also provides the underrange or overrange indication. If both Bit 16 and Bit 15 are HIGH, the differential input voltage is above +FS. If both Bit 16 and Bit 15 are LOW, the differential input voltage is below -FS. The function of these bits is summarized in Table 1.
Table 1. LTC2436-1 Status Bits
Input Range VIN 0.5 * VREF 0V VIN < 0.5 * VREF -0.5 * VREF VIN < 0V VIN < - 0.5 * VREF Bit 18 Bit 17 Bit 16 Bit 15 EOC CH0/CH1 SIG MSB 0 0 0 0 0 or 1 0 or 1 0 or 1 0 or 1 1 1 0 0 1 0 1 0
Bits 15-0 are the 16-Bit conversion result MSB first. Bit 0 is the least significant bit (LSB). Data is shifted out of the SDO pin under control of the serial clock (SCK), see Figure 3. Whenever CS is HIGH, SDO
CS
BIT 18 SDO Hi-Z EOC
BIT 17 CH0/CH1
BIT 16 SIG
SCK
1 SLEEP
2
Figure 3. Output Data Timing
24361f
10
U
remains high impedance and any externally generated SCK clock pulses are ignored by the internal data out shift register. In order to shift the conversion result out of the device, CS must first be driven LOW. EOC is seen at the SDO pin of the device once CS is pulled LOW. EOC changes real time from HIGH to LOW at the completion of a conversion. This signal may be used as an interrupt for an external microcontroller. Bit 18 (EOC) can be captured on the first rising edge of SCK. Bit 17 is shifted out of the device on the first falling edge of SCK. The final data bit (Bit 0) is shifted out on the falling edge of the 18th SCK and may be latched on the rising edge of the 19th SCK pulse. On the falling edge of the 19th SCK pulse, SDO goes HIGH indicating the initiation of a new conversion cycle. This bit serves as EOC (Bit 18) for the next conversion cycle. Table 2 summarizes the output data format. In order to remain compatible with some SPI microcontrollers, more than 19 SCK clock pulses may be applied. As long as these clock edges are complete before the conversion ends, they will not effect the serial data. However, switching SCK during a conversion may generate ground currents in the device leading to extra offset and noise error sources. As long as the voltage on the analog input pins is maintained within the - 0.3V to (VCC + 0.3V) absolute maximum operating range, a conversion result is generated for any differential input voltage VIN from -FS = -0.5 * VREF to +FS = 0.5 * VREF. For differential input voltages greater than +FS, the conversion result is clamped to the value corresponding to the +FS + 1LSB. For differential input voltages
BIT 15 MSB BIT 14 BIT 1 BIT 0 LSB16 3 4 5 17 18 19 CONVERSION
24361 F03
W
UU
DATA OUTPUT
LTC2436-1
APPLICATIO S I FOR ATIO
Table 2. LTC2436-1 Output Data Format
Differential Input Voltage VIN * VIN* 0.5 * VREF** 0.5 * VREF** - 1LSB 0.25 * VREF** 0.25 * VREF** - 1LSB 0 -1LSB - 0.25 * VREF** - 0.25 * VREF** - 1LSB - 0.5 * VREF** VIN* < -0.5 * VREF** Bit 18 EOC 0 0 0 0 0 0 0 0 0 0
Bit 17 CH0/CH1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1
*The differential input voltage VIN = IN+ - IN-. **The differential reference voltage VREF = REF+ - REF-.
-80
-80 -85
NORMAL MODE REECTION RATIO (dB)
NORMAL MODE REJECTION (dB)
-90 -100 -100 -120 -130 -140 48 50 52 54 56 58 60 62 DIFFERENTIAL INPUT SIGNAL FREQUENCY (Hz)
24361 F04
Figure 4. LTC2436-1 Normal Mode Rejection When Using an Internal Oscillator
below -FS, the conversion result is clamped to the value corresponding to -FS - 1LSB. Simultaneous Frequency Rejection The LTC2436-1 internal oscillator provides better than 87dB normal mode rejection over the range of 49Hz to 61.2Hz as shown in Figure 4. For this simultaneous 50Hz/ 60Hz rejection, FO should be connected to GND. When a fundamental rejection frequency different from the range 49Hz to 61.2Hz is required or when the converter must be sychronized with an outside source, the LTC2436-1 can operate with an external conversion clock. The conveter
U
Bit 16 SIG 1 1 1 1 1 0 0 0 0 0 Bit 15 MSB 1 0 0 0 0 1 1 1 1 0 Bit 14 0 1 1 0 0 1 1 0 0 1 Bit 13 0 1 0 1 0 1 0 1 0 1 Bit 12 0 1 0 1 0 1 0 1 0 1 ... ... ... ... ... ... ... ... ... ... ... Bit 0 0 1 0 1 0 1 0 1 0 1
-90 -95 -100 -105 -110 -115 -120 -125 -130 -135 -140 -12 -8 -4 0 4 8 12 DIFFERENTIAL INPUT SIGNAL FREQUENCY DEVIATION FROM NOTCH FREQUENCY fEOSC/2560(%)
24361 F05
W
UU
Figure 5. LTC2436-1 Normal Mode Rejection When Using an External Oscillator of Frequency fEOSC
automatically detects the presence of an external clock signal at the FO pin and turns off the internal oscillator. The frequency fEOSC of the external signal must be at least 2560Hz to be detected. The external clock signal duty cycle is not significant as long as the minimum and maximum specifications for the high and low periods, tHEO and tLEO, are observed. While operating with an external conversion clock of a frequency fEOSC, the LTC2436-1 provides better than 110dB normal mode rejection in a frequency range fEOSC/2560 4%. The normal mode rejection as a function of the input frequency deviation from fEOSC/2560 is shown in Figure 5.
24361f
11
LTC2436-1
APPLICATIO S I FOR ATIO
Whenever an external clock is not present at the FO pin the converter automatically activates its internal oscillator and enters the Internal Conversion Clock mode. The LTC2436-1 operation will not be disturbed if the change of conversion clock source occurs during the sleep state or during the data output state while the converter uses an external serial clock. If the change occurs during the conversion state, the result of the conversion in progress may be outside specifications but the following conversions will not be affected. If the change occurs during the data output state and the converter is in the Internal SCK mode, the serial clock duty cycle may be affected but the serial data stream will remain valid. Table 3 summarizes the duration of each state and the achievable output data rate as a function of FO. SERIAL INTERFACE PINS The LTC2436-1 transmits the conversion results and receives the start of conversion command through a synchronous 3-wire interface. During the conversion and sleep states, this interface can be used to assess the converter status and during the data output state it is used to read the conversion result. Serial Clock Input/Output (SCK) The serial clock signal present on SCK (Pin 13) is used to synchronize the data transfer. Each bit of data is shifted out the SDO pin on the falling edge of the serial clock.
Table 3. LTC2436-1 State Duration
State CONVERT Operating Mode Internal Oscillator External Oscillator
FO = LOW Simultaneous 50Hz/60Hz Rejection FO = External Oscillator with Frequency fEOSC kHz (fEOSC/2560 Rejection) FO = LOW (Internal Oscillator) FO = External Oscillator with Frequency fEOSC kHz
SLEEP DATA OUTPUT Internal Serial Clock
External Serial Clock with Frequency fSCK kHz
12
U
In the Internal SCK mode of operation, the SCK pin is an output and the LTC2436-1 creates its own serial clock by dividing the internal conversion clock by 8. In the External SCK mode of operation, the SCK pin is used as input. The internal or external SCK mode is selected on power-up and then reselected every time a HIGH-to-LOW transition is detected at the CS pin. If SCK is HIGH or floating at powerup or during this transition, the converter enters the internal SCK mode. If SCK is LOW at power-up or during this transition, the converter enters the external SCK mode. Serial Data Output (SDO) The serial data output pin, SDO (Pin 12), provides the result of the last conversion as a serial bit stream (MSB first) during the data output state. In addition, the SDO pin is used as an end of conversion indicator during the conversion and sleep states. When CS (Pin 11) is HIGH, the SDO driver is switched to a high impedance state. This allows sharing the serial interface with other devices. If CS is LOW during the convert or sleep state, SDO will output EOC. If CS is LOW during the conversion phase, the EOC bit appears HIGH on the SDO pin. Once the conversion is complete, EOC goes LOW. Chip Select Input (CS) The active LOW chip select, CS (Pin 11), is used to test the conversion status and to enable the data output transfer as described in the previous sections.
Duration 147ms, Output Data Rate 6.8 Readings/s 20510/fEOSCs, Output Data Rate fEOSC/20510 Readings/s As Long As CS = HIGH Until CS = LOW and SCK As Long As CS = LOW But Not Longer Than 1.09ms (19 SCK cycles) As Long As CS = LOW But Not Longer Than 152/fEOSCms (19 SCK cycles) As Long As CS = LOW But Not Longer Than 19/fSCKms (19 SCK cycles)
24361f
W
UU
LTC2436-1
APPLICATIO S I FOR ATIO
In addition, the CS signal can be used to trigger a new conversion cycle before the entire serial data transfer has been completed. The LTC2436-1 will abort any serial data transfer in progress and start a new conversion cycle anytime a LOW-to-HIGH transition is detected at the CS pin after the converter has entered the data output state (i.e., after the first rising edge of SCK occurs with CS = LOW). Finally, CS can be used to control the free-running modes of operation, see Serial Interface Timing Modes section. Grounding CS will force the ADC to continuously convert at the maximum output rate selected by FO. SERIAL INTERFACE TIMING MODES The LTC2436-1's 3-wire interface is SPI and MICROWIRE compatible. This interface offers several flexible modes of
Table 4. LTC2436-1 Interface Timing Modes
SCK Source External External Internal Internal
2.7V TO 5.5V 1F 1 2 3 4 5 ANALOG INPUT RANGE -0.5VREF TO 0.5VREF 6 7 VCC
Configuration External SCK, Single Cycle Conversion External SCK, 2-Wire I/O Internal SCK, Single Cycle Conversion Internal SCK, 2-Wire I/O, Continuous Conversion
CS TEST EOC SDO Hi-Z Hi-Z TEST EOC
BIT 18 EOC
BIT 17 CH0/CH1
SCK (EXTERNAL) CONVERSION SLEEP SLEEP DATA OUTPUT CONVERSION
24361 F06
TEST EOC (OPTIONAL)
Figure 6. External Serial Clock, Single Cycle Operation
24361f
U
operation. These include internal/external serial clock, 2- or 3-wire I/O, single cycle conversion and autostart. The following sections describe each of these serial interface timing modes in detail. In all these cases, the converter can use the internal oscillator (FO = LOW) or an external oscillator connected to the FO pin. Refer to Table 4 for a summary. External Serial Clock, Single Cycle Operation (SPI/MICROWIRE Compatible) This timing mode uses an external serial clock to shift out the conversion result and a CS signal to monitor and control the state of the conversion cycle, see Figure 6. The serial clock mode is selected on the falling edge of CS. To select the external serial clock mode, the serial clock pin (SCK) must be LOW during each CS falling edge.
Conversion Cycle Control CS and SCK SCK CS Continuous Data Output Control CS and SCK SCK CS Internal Connection and Waveforms Figures 6, 7 Figure 8 Figures 9, 10 Figure 11
FO 14 LTC2436-1 REF + REF - CH0+ CH0- CH1+ CH1- GND 8, 9, 10, 15, 16 SCK SDO CS 13 12 11 3-WIRE SPI INTERFACE = EXTERNAL CLOCK SOURCE = INTERNAL OSC/SIMULTANEOUS 50Hz/60Hz REJECTION REFERENCE VOLTAGE 0.1V TO VCC BIT 16 SIG BIT 15 MSB BIT 14 BIT 13 BIT 2 BIT 1 BIT 0 LSB Hi-Z
W
UU
13
LTC2436-1
APPLICATIO S I FOR ATIO
The serial data output pin (SDO) is Hi-Z as long as CS is HIGH. At any time during the conversion cycle, CS may be pulled LOW in order to monitor the state of the converter. While CS is pulled LOW, EOC is output to the SDO pin. EOC = 1 while a conversion is in progress and EOC = 0 if the device is in the sleep state. With CS high, the device automatically enters the low power sleep state once the conversion is complete. When the device is in the sleep state (EOC = 0), its conversion result is held in an internal static shift register. Data is shifted out the SDO pin on each falling edge of SCK. This enables external circuitry to latch the output on the rising edge of SCK. EOC can be latched on the first rising edge of SCK and the last bit of the conversion result can be latched on the 19th rising edge of SCK. On the 19th falling edge of SCK, the device begins a new conversion.
2.7V TO 5.5V 1F 1 2 3 4 5 ANALOG INPUT RANGE -0.5VREF TO 0.5VREF 6 7
CS TEST EOC TEST EOC
BIT 0 SDO EOC
Hi-Z
Hi-Z
Hi-Z
SCK (EXTERNAL) SLEEP DATA OUTPUT CONVERSION SLEEP DATA OUTPUT SLEEP CONVERSION
24361 F07
TEST EOC (OPTIONAL)
Figure 7. External Serial Clock, Reduced Data Output Length
14
U
SDO goes HIGH (EOC = 1) indicating a conversion is in progress. At the conclusion of the data cycle, CS may remain LOW and EOC monitored as an end-of-conversion interrupt. Alternatively, CS may be driven HIGH setting SDO to Hi-Z. As described above, CS may be pulled LOW at any time in order to monitor the conversion status. Typically, CS remains LOW during the data output state. However, the data output state may be aborted by pulling CS HIGH anytime between the first rising edge and the 19th falling edge of SCK, see Figure 7. On the rising edge of CS, the device aborts the data output state and immediately initiates a new conversion. This is useful for aborting an invalid conversion cycle or synchronizing the start of a conversion.
VCC REF + REF - CH0+ CH0- CH1+ CH1- GND 8, 9, 10, 15, 16 SCK SDO CS 13 12 11 3-WIRE SPI INTERFACE FO 14 LTC2436-1 = EXTERNAL CLOCK SOURCE = INTERNAL OSC/SIMULTANEOUS 50Hz/60Hz REJECTION REFERENCE VOLTAGE 0.1V TO VCC BIT 18 EOC BIT 17 CH0/CH1 BIT 16 SIG BIT 15 MSB Hi-Z BIT 14 BIT 5 BIT 4
24361f
W
UU
LTC2436-1
APPLICATIO S I FOR ATIO
External Serial Clock, 2-Wire I/O
This timing mode utilizes a 2-wire serial I/O interface. The conversion result is shifted out of the device by an externally generated serial clock (SCK) signal, see Figure 8. CS may be permanently tied to ground, simplifying the user interface or isolation barrier. The external serial clock mode is selected at the end of the power-on reset (POR) cycle. The POR cycle is concluded typically 1ms after VCC exceeds 2V. The level applied to SCK at this time determines if SCK is internal or external. SCK must be driven LOW prior to the end of POR in order to enter the external serial clock timing mode. Since CS is tied LOW, the end-of-conversion (EOC) can be continuously monitored at the SDO pin during the convert and sleep states. EOC may be used as an interrupt to an external controller indicating the conversion result is ready. EOC = 1 while the conversion is in progress and EOC = 0 once the conversion ends. On the falling edge of EOC, the conversion result is loaded into an internal static shift register. Data is shifted out the SDO pin on each falling edge of SCK enabling external circuitry to latch data on the rising edge of SCK. EOC can be latched on the first rising edge of SCK. On the 19th falling edge of SCK, SDO goes HIGH (EOC = 1) indicating a new conversion has begun.
2.7V TO 5.5V 1F 1 2 3 4 5 ANALOG INPUT RANGE -0.5VREF TO 0.5VREF 6 7
CS
BIT 18 SDO EOC
BIT 17 CH0/CH1
SCK (EXTERNAL) CONVERSION DATA OUTPUT CONVERSION
24361 F08
Figure 8. External Serial Clock, CS = 0 Operation (2-Wire)
24361f
U
Internal Serial Clock, Single Cycle Operation This timing mode uses an internal serial clock to shift out the conversion result and a CS signal to monitor and control the state of the conversion cycle, see Figure 9. In order to select the internal serial clock timing mode, the serial clock pin (SCK) must be floating (Hi-Z) or pulled HIGH prior to the falling edge of CS. The device will not enter the internal serial clock mode if SCK is driven LOW on the falling edge of CS. An internal weak pull-up resistor is active on the SCK pin during the falling edge of CS; therefore, the internal serial clock timing mode is automatically selected if SCK is not externally driven. The serial data output pin (SDO) is Hi-Z as long as CS is HIGH. At any time during the conversion cycle, CS may be pulled LOW in order to monitor the state of the converter. Once CS is pulled LOW, SCK goes LOW and EOC is output to the SDO pin. EOC = 1 while a conversion is in progress and EOC = 0 if the device is in the sleep state. When testing EOC, if the conversion is complete (EOC = 0), the device will exit the sleep state during the EOC test. In order to allow the device to return to the low power sleep state, CS must be pulled HIGH before the first rising edge of SCK. In the internal SCK timing mode, SCK goes HIGH
VCC REF + REF - CH0+ CH0- CH1+ CH1- GND 8, 9, 10, 15, 16 SCK SDO CS 13 12 11 2-WIRE INTERFACE FO 14 LTC2436-1 = EXTERNAL CLOCK SOURCE = INTERNAL OSC/SIMULTANEOUS 50Hz/60Hz REJECTION REFERENCE VOLTAGE 0.1V TO VCC BIT 16 SIG BIT 15 MSB BIT 14 BIT 13 BIT 2 BIT 1 BIT 0 LSB
W
UU
15
LTC2436-1
APPLICATIO S I FOR ATIO
ANALOG INPUT RANGE -0.5VREF TO 0.5VREF
BIT 18 SDO Hi-Z Hi-Z EOC
BIT 17 CH0/CH1
SCK (INTERNAL) CONVERSION SLEEP SLEEP DATA OUTPUT CONVERSION
24361 F09
TEST EOC (OPTIONAL)
Figure 9. Internal Serial Clock, Single Cycle Operation
and the device begins outputting data at time tEOCtest after the falling edge of CS (if EOC = 0) or tEOCtest after EOC goes LOW (if CS is LOW during the falling edge of EOC). The value of tEOCtest is 23s if the device is using its internal oscillator (F0 = logic LOW). If FO is driven by an external oscillator of frequency fEOSC, then tEOCtest is 3.6/fEOSC. If CS is pulled HIGH before time tEOCtest, the device returns to the sleep state and the conversion result is held in the internal static shift register. If CS remains LOW longer than tEOCtest, the first rising edge of SCK will occur and the conversion result is serially shifted out of the SDO pin. The data output cycle concludes after the 19th rising edge. Data is shifted out the SDO pin on each falling edge of SCK. The internally generated serial clock is output to the SCK pin. This signal may be used to shift the conversion result into external circuitry. EOC can be latched on the first rising edge of SCK and the last bit of the conversion result on the 19th rising edge of SCK. After the 19th rising edge, SDO goes HIGH (EOC = 1), SCK stays HIGH and a new conversion starts.
16
U
2.7V TO 5.5V 1F 1 2 3 4 5 6 7 VCC REF + REF - CH0
+
W
UU
VCC 14 = EXTERNAL CLOCK SOURCE = INTERNAL OSC/SIMULTANEOUS 50Hz/60Hz REJECTION
FO
10k
LTC2436-1 13 12 11
REFERENCE VOLTAGE 0.1V TO VCC
SCK SDO CS
3-WIRE SPI INTERFACE
CH0- CH1+ CH1-
GND
8, 9, 10, 15, 16
BIT 16 SIG
BIT 15 MSB
BIT 14
BIT 13
BIT 2
BIT 1
BIT 0 LSB
Hi-Z
Hi-Z
Typically, CS remains LOW during the data output state. However, the data output state may be aborted by pulling CS HIGH anytime between the first and 19th rising edge of SCK, see Figure 10. On the rising edge of CS, the device aborts the data output state and immediately initiates a new conversion. This is useful for aborting an invalid conversion cycle, or synchronizing the start of a conversion. If CS is pulled HIGH while the converter is driving SCK LOW, the internal pull-up is not available to restore SCK to a logic HIGH state. This will cause the device to exit the internal serial clock mode on the next falling edge of CS. This can be avoided by adding an external 10k pull-up resistor to the SCK pin or by never pulling CS HIGH when SCK is LOW. Whenever SCK is LOW, the LTC2436-1's internal pull-up at pin SCK is disabled. Normally, SCK is not externally driven if the device is in the internal SCK timing mode. However, certain applications may require an external driver on SCK. If this driver goes Hi-Z after outputting a LOW signal, the LTC2436-1's internal pull-up remains
24361f
LTC2436-1
APPLICATIO S I FOR ATIO
ANALOG INPUT RANGE -0.5VREF TO 0.5VREF
> tEOCtest CS TEST EOC
BIT 0 SDO Hi-Z EOC Hi-Z
Hi-Z
Hi-Z
SCK (INTERNAL) SLEEP DATA OUTPUT CONVERSION SLEEP SLEEP DATA OUTPUT CONVERSION
24361 F10
TEST EOC (OPTIONAL)
Figure 10. Internal Serial Clock, Reduced Data Output Length
disabled. Hence, SCK remains LOW. On the next falling edge of CS, the device is switched to the external SCK timing mode. By adding an external 10k pull-up resistor to SCK, this pin goes HIGH once the external driver goes Hi-Z. On the next CS falling edge, the device will remain in the internal SCK timing mode. A similar situation may occur during the sleep state when CS is pulsed HIGH-LOW-HIGH in order to test the conversion status. If the device is in the sleep state (EOC = 0), SCK will go LOW. Once CS goes HIGH (within the time period defined above as tEOCtest), the internal pull-up is activated. For a heavy capacitive load on the SCK pin, the internal pull-up may not be adequate to return SCK to a HIGH level before CS goes low again. This is not a concern under normal conditions where CS remains LOW after detecting EOC = 0. This situation is easily overcome by adding an external 10k pull-up resistor to the SCK pin.
U
2.7V TO 5.5V 1F 1 2 3 4 5 6 7 VCC REF + REF - CH0+ CH0- CH1+ CH1- GND 8, 9, 10, 15, 16 SCK SDO CS 13 12 11 3-WIRE SPI INTERFACE FO 14 = EXTERNAL CLOCK SOURCE = INTERNAL OSC/SIMULTANEOUS 50Hz/60Hz REJECTION VCC LTC2436-1 10k REFERENCE VOLTAGE 0.1V TO VCC BIT 18 EOC BIT 17 CH0/CH1 BIT 16 SIG BIT 15 MSB Hi-Z BIT 14 BIT 13 BIT 2 TEST EOC
W
UU
Internal Serial Clock, 2-Wire I/O, Continuous Conversion This timing mode uses a 2-wire, all output (SCK and SDO) interface. The conversion result is shifted out of the device by an internally generated serial clock (SCK) signal, see Figure 11. CS may be permanently tied to ground, simplifying the user interface or isolation barrier. The internal serial clock mode is selected at the end of the power-on reset (POR) cycle. The POR cycle is concluded approximately 1ms after VCC exceeds 2V. An internal weak pull-up is active during the POR cycle; therefore, the internal serial clock timing mode is automatically selected if SCK is not externally driven LOW (if SCK is loaded such that the internal pull-up cannot pull the pin HIGH, the external SCK mode will be selected).
24361f
17
LTC2436-1
APPLICATIO S I FOR ATIO
ANALOG INPUT RANGE -0.5VREF TO 0.5VREF
CS
SDO
BIT 18 EOC
BIT 17 CH0/CH1
BIT 16 SIG
SCK (INTERNAL) CONVERSION DATA OUTPUT CONVERSION
24361 F11
Figure 11. Internal Serial Clock, Continuous Operation
During the conversion, the SCK and the serial data output pin (SDO) are HIGH (EOC = 1). Once the conversion is complete, SCK and SDO go LOW (EOC = 0) indicating the conversion has finished and the device has entered the data output state. The data output cycle begins on the first rising edge of SCK and ends after the 19th rising edge. Data is shifted out the SDO pin on each falling edge of SCK. The internally generated serial clock is output to the SCK pin. This signal may be used to shift the conversion result into external circuitry. EOC can be latched on the first rising edge of SCK and the last bit of the conversion result can be latched on the 19th rising edge of SCK. After the 19th rising edge, SDO goes HIGH (EOC = 1) indicating a new conversion is in progress. SCK remains HIGH during the conversion. PRESERVING THE CONVERTER ACCURACY The LTC2436-1 is designed to reduce as much as possible the conversion result sensitivity to device decoupling, PCB layout, antialiasing circuits, line frequency perturbations and so on. Nevertheless, in order to preserve the accuracy capability of this part, some simple precautions are desirable.
18
U
2.7V TO 5.5V 1F 1 2 3 4 5 6 7 VCC REF + REF - CH0
+
W
UU
FO
14
LTC2436-1 13 12 11
= EXTERNAL CLOCK SOURCE = INTERNAL OSC/SIMULTANEOUS 50Hz/60Hz REJECTION
REFERENCE VOLTAGE 0.1V TO VCC
SCK SDO CS
2-WIRE INTERFACE
CH0- CH1+ CH1-
GND
8, 9, 10, 15, 16
BIT 15 MSB
BIT 14
BIT 13
BIT 2
BIT 1
BIT 0 LSB
Digital Signal Levels The LTC2436-1's digital interface is easy to use. Its digital inputs (FO, CS and SCK in External SCK mode of operation) accept standard TTL/CMOS logic levels and the internal hysteresis receivers can tolerate edge rates as slow as 100s. However, some considerations are required to take advantage of the exceptional accuracy and low supply current of this converter. The digital output signals (SDO and SCK in Internal SCK mode of operation) are less of a concern because they are not generally active during the conversion state. While a digital input signal is in the range 0.5V to (VCC - 0.5V), the CMOS input receiver draws additional current from the power supply. It should be noted that, when any one of the digital input signals (FO, CS and SCK in External SCK mode of operation) is within this range, the LTC2436-1 power supply current may increase even if the signal in question is at a valid logic level. For micropower operation, it is recommended to drive all digital input signals to full CMOS levels [VIL < 0.4V and VOH > (VCC - 0.4V)].
24361f
LTC2436-1
APPLICATIO S I FOR ATIO
During the conversion period, the undershoot and/or overshoot of a fast digital signal connected to the LTC2436-1 pins may severely disturb the analog to digital conversion process. Undershoot and overshoot can occur because of the impedance mismatch at the converter pin when the transition time of an external control signal is less than twice the propagation delay from the driver to LTC2436-1. For reference, on a regular FR-4 board, signal propagation velocity is approximately 183ps/inch for internal traces and 170ps/inch for surface traces. Thus, a driver generating a control signal with a minimum transition time of 1ns must be connected to the converter pin through a trace shorter than 2.5 inches. This problem becomes particularly difficult when shared control lines are used and multiple reflections may occur. The solution is to carefully terminate all transmission lines close to their characteristic impedance. Parallel termination near the LTC2436-1 pin will eliminate this problem but will increase the driver power dissipation. A series resistor between 27 and 56 placed near the driver will also eliminate this problem without additional power dissipation. The actual resistor value depends upon the trace impedance and connection topology. An alternate solution is to reduce the edge rate of the control signals. It should be noted that using very slow edges will increase the converter power supply current during the transition time. The multiple ground pins used in this package configuration, as well as the differential input and reference architecture, reduce substantially the converter's sensitivity to ground currents. Particular attention must be given to the connection of the FO signal when the LTC2436-1 is used with an external conversion clock. This clock is active during the conversion time and the normal mode rejection provided by the internal digital filter is not very high at this frequency. A normal mode signal of this frequency at the converter reference terminals may result into DC gain and INL errors. A normal mode signal of this frequency at the converter input terminals may result into a DC offset error.
U
Such perturbations may occur due to asymmetric capacitive coupling between the FO signal trace and the converter input and/or reference connection traces. An immediate solution is to maintain maximum possible separation between the FO signal trace and the input/reference signals. When the FO signal is parallel terminated near the converter, substantial AC current is flowing in the loop formed by the FO connection trace, the termination and the ground return path. Thus, perturbation signals may be inductively coupled into the converter input and/or reference. In this situation, the user must reduce to a minimum the loop area for the FO signal as well as the loop area for the differential input and reference connections. Driving the Input and Reference The input and reference pins of the LTC2436-1 converter are directly connected to a network of sampling capacitors. Depending upon the relation between the differential input voltage and the differential reference voltage, these capacitors are switching between these four pins transfering small amounts of charge in the process. A simplified equivalent circuit is shown in Figure 12, where IN+ and IN- refer to the selected differential channel and the unselected channel is omitted for simplicity. For a simple approximation, the source impedance RS driving an analog input pin (IN+, IN-, REF+ or REF-) can be considered to form, together with RSW and CEQ (see Figure 12), a first order passive network with a time constant = (RS + RSW) * CEQ. The converter is able to sample the input signal with better than 1LSB accuracy if the sampling period is at least 11 times greater than the input circuit time constant . The sampling process on the four input analog pins is quasi-independent so each time constant should be considered by itself and, under worstcase circumstances, the errors may add. When using the internal oscillator (FO = LOW), the LTC2436-1's front-end switched-capacitor network is clocked at 69900Hz corresponding to a 14.3s sampling
24361f
W
UU
19
LTC2436-1
APPLICATIO S I FOR ATIO
IREF+ VREF+ ILEAK IIN+ VIN+ ILEAK IIN - VIN - ILEAK IREF - VREF - ILEAK VCC ILEAK RSW (TYP) 20k VCC ILEAK RSW (TYP) 20k VCC ILEAK RSW (TYP) 20k VCC ILEAK RSW (TYP) 20k
24361 F12
SWITCHING FREQUENCY fSW = 69.900Hz INTERNAL OSCILLATOR (FO = LOW OR HIGH) fSW = 0.5 * fEOSC EXTERNAL OSCILLATOR
Figure 12. LTC2436-1 Equivalent Analog Input Circuit
period. Thus, for settling errors of less than 1LSB, the driving source impedance should be chosen such that 14.3s/11 = 1.3s. When an external oscillator of frequency fEOSC is used, the sampling period is 2/fEOSC and, for a settling error of less than 1LSB, 0.18/fEOSC. Input Current If complete settling occurs on the input, conversion results will be unaffected by the dynamic input current. An incomplete settling of the input signal sampling process may result in gain and offset errors, but it will not degrade the INL performance of the converter. Figure 12 shows the mathematical expressions for the average bias currents flowing through the IN + and IN - pins as a result of the sampling charge transfers when integrated over a substantial time period (longer than 64 internal clock cycles). The effect of this input dynamic current can be analyzed using the test circuit of Figure 13. The CPAR capacitor includes the LTC2436-1 pin capacitance (5pF typical) plus the capacitance of the test fixture used to obtain the results shown in Figures 14 and 15. A careful implementation can bring the total input capacitance (CIN + CPAR) closer to 5pF thus achieving better performance than the one predicted
+FS ERROR (LSB)
20
U
I IN+ I IN-
W
UU
( )AVG = VIN + VINCMR-EQVREFCM 0.5 *
- ( )AVG = - VIN + 0V.INCM EQVREFCM 5*R
I REF + I REF - where:
(
)AVG = 1.5 * VREF0-5V*INCM + VREFCM - VREF INREQ * . REQ
V )AVG = -1.5 * VREF0.- *INCM + VREFCM + VREF INREQ 5 REQ * V2
V2
CEQ 18pF (TYP)
(
VREF = REF + - REF - REF + + REF - VREFCM = 2 VIN = IN+ - IN- IN+ - IN- VINCM = 2
REQ = 3.97M INTERNAL OSCILLATOR 50Hz / 60Hz Notch (FO = LOW) REQ = 0.555 * 1012 / fEOSC EXTERNAL OSCILLATOR
(
)
RSOURCE CPAR 20pF
IN + CIN
VINCM + 0.5VIN
LTC2436-1
RSOURCE CPAR 20pF
IN - CIN
24361 F13
VINCM - 0.5VIN
Figure 13. An RC Network at IN + and IN -
3 CIN = 0.01F CIN = 0.001F CIN = 100pF 2 CIN = 0pF VCC = 5V REF + = 5V REF - = GND IN + = 5V IN - = 2.5V FO = GND TA = 25C 1 10 100 1k RSOURCE () 10k 100k
24361 F14
1
0
Figure 14. +FS Error vs RSOURCE at IN+ or IN- (Small CIN)
24361f
LTC2436-1
APPLICATIO S I FOR ATIO
0 VCC = 5V REF + = 5V REF - = GND IN + = GND IN - = 2.5V FO = GND TA = 25C CIN = 0.01F -2 CIN = 0.001F CIN = 100pF -3 1 10 CIN = 0pF 100 1k RSOURCE () 10k 100k
24361 F15
-FS ERROR (LSB)
+FS ERROR (LSB)
-1
Figure 15. -FS Error vs RSOURCE at IN+ or IN- (Small CIN)
0 CIN = 0.01F -4
-FS ERROR (LSB)
-8 CIN = 0.1F -12 VCC = 5V REF + = 5V REF - = GND IN + = 1.25V IN - = 3.75V FO = GND TA = 25C
-16
CIN = 1F, 10F
-20
0 100 200 300 400 500 600 700 800 900 1000 RSOURCE ()
24361 F17
Figure 17. -FS Error vs RSOURCE at IN+ or IN- (Large CIN)
by Figures 14 and 15. For simplicity, two distinct situations can be considered. For relatively small values of input capacitance (CIN < 0.01F), the voltage on the sampling capacitor settles almost completely and relatively large values for the source impedance result in only small errors. Such values for CIN will deteriorate the converter offset and gain performance without significant benefits of signal filtering and the user is advised to avoid them. Nevertheless, when small values of CIN are unavoidably present as parasitics of input multiplexers, wires, connectors or sensors, the LTC2436-1 can maintain its accuracy while operating with relative large values of source resistance as shown in
U
20 16 12 VCC = 5V REF + = 5V REF - = GND IN + = 3.75V IN - = 1.25V FO = GND TA = 25C CIN = 1F, 10F CIN = 0.1F 8 CIN = 0.01F 4 0 0 100 200 300 400 500 600 700 800 900 1000 RSOURCE ()
24361 F16
W
UU
Figure 16. +FS Error vs RSOURCE at IN+ or IN- (Large CIN)
Figures 14 and 15. These measured results may be slightly different from the first order approximation suggested earlier because they include the effect of the actual second order input network together with the nonlinear settling process of the input amplifiers. For small CIN values, the settling on IN+ and IN - occurs almost independently and there is little benefit in trying to match the source impedance for the two pins. Larger values of input capacitors (CIN > 0.01F) may be required in certain configurations for antialiasing or general input signal filtering. Such capacitors will average the input sampling charge and the external source resistance will see a quasi constant input differential impedance. When FO = LOW (internal oscillator and 50Hz/60Hz notch), the typical differential input resistance is 2M which will generate a gain error of approximately 1LSB at full scale for each 60 of source resistance driving IN+ or IN -. When FO is driven by an external oscillator with a frequency fEOSC (external conversion clock operation), the typical differential input resistance is 0.28 * 1012/fEOSC and each ohm of source resistance driving IN+ or IN - will result in 1.11 * 10 -7 * fEOSCLSB gain error at full scale. The effect of the source resistance on the two input pins is additive with respect to this gain error. The typical +FS and -FS errors as a function of the sum of the source resistance seen by IN+ and IN- for large values of CIN are shown in Figures 16 and 17.
24361f
21
LTC2436-1
APPLICATIO S I FOR ATIO
In addition to this gain error, an offset error term may also appear. The offset error is proportional with the mismatch between the source impedance driving the two input pins IN+ and IN- and with the difference between the input and reference common mode voltages. While the input drive circuit nonzero source impedance combined with the converter average input current will not degrade the INL performance, indirect distortion may result from the modulation of the offset error by the common mode component of the input signal. Thus, when using large CIN capacitor values, it is advisable to carefully match the source impedance seen by the IN+ and IN- pins. When FO = LOW (internal oscillator and 50Hz/60Hz notch), every 60 mismatch in source impedance transforms a full-scale common mode input signal into a differential mode input signal of 1LSB. When FO is driven by an external oscillator with a frequency fEOSC, every 1 mismatch in source impedance transforms a full-scale common mode input signal into a differential mode input signal of 1.11 * 10-7 * fEOSCLSB. Figure 18 shows the typical offset error due to input common mode voltage for various values of source resistance imbalance between the IN+ and IN- pins when large CIN values are used.
8 A VCC = 5V REF + = 5V REF - = GND IN + = IN - = VINCM
OFFSET ERROR (LSB)
4
B C D E F
0
-4
G
-8
FO = GND TA = 25C RSOURCEIN - = 500 CIN = 10F 1 1.5 2 2.5 3 VINCM (V) 3.5 4 4.5 5
0
0.5
A: RIN = +400 B: RIN = +200 C: RIN = +100 D: RIN = 0
E: RIN = -100 F: RIN = -200 G: RIN = -400
24361 F18
Figure 18. Offset Error vs Common Mode Voltage (VINCM = IN+ = IN-) and Input Source Resistance Imbalance (RIN = RSOURCEIN+ - RSOURCEIN-) for Large CIN Values (CIN 1F)
22
U
If possible, it is desirable to operate with the input signal common mode voltage very close to the reference signal common mode voltage as is the case in the ratiometric measurement of a symmetric bridge. This configuration eliminates the offset error caused by mismatched source impedances. The magnitude of the dynamic input current depends upon the size of the very stable internal sampling capacitors and upon the accuracy of the converter sampling clock. The accuracy of the internal clock over the entire temperature and power supply range is typically better than 0.5%. Such a specification can also be easily achieved by an external clock. When relatively stable resistors (50ppm/C) are used for the external source impedance seen by IN+ and IN-, the expected drift of the dynamic current, offset and gain errors will be insignificant (about 1% of their respective values over the entire temperature and voltage range). Even for the most stringent applications, a one-time calibration operation may be sufficient. In addition to the input sampling charge, the input ESD protection diodes have a temperature dependent leakage current. This current, nominally 1nA (10nA max), results in a small offset shift. A 15k source resistance will create a 0LSB typical and 1LSB maximum offset voltage. Reference Current In a similar fashion, the LTC2436-1 samples the differential reference pins REF+ and REF- transfering small amount of charge to and from the external driving circuits thus producing a dynamic reference current. This current does not change the converter offset, but it may degrade the gain and INL performance. The effect of this current can be analyzed in the same two distinct situations. For relatively small values of the external reference capacitors (CREF < 0.01F), the voltage on the sampling capacitor settles almost completely and relatively large values for the source impedance result in only small errors. Such values for CREF will deteriorate the converter offset and gain performance without significant benefits of reference filtering and the user is advised to avoid them.
24361f
W
UU
LTC2436-1
APPLICATIO S I FOR ATIO
Larger values of reference capacitors (CREF > 0.01F) may be required as reference filters in certain configurations. Such capacitors will average the reference sampling charge and the external source resistance will see a quasi constant reference differential impedance. When FO = LOW (internal oscillator and 50Hz/60Hz notch), the typical differential reference resistance is 1.4M which will generate a gain error of approximately 1LSB full scale for each 40 of source resistance driving REF+ or REF-. When FO is driven by an external oscillator with a frequency fEOSC (external conversion clock operation), the typical differential reference resistance is 0.20 * 1012/fEOSC and each ohm of source resistance drving REF+ or REF- will result in 1.54 * 10-7 * fEOSCLSB gain error at full scale. The effect
0 VCC = 5V REF + = 5V REF - = GND IN + = 5V IN - = 2.5V FO = GND TA = 25C CREF = 0.01F -2 CREF = 0.001F CREF = 100pF -3 1 10 CREF = 0pF 100 1k RSOURCE () 10k 100k
24361 F19
-FS ERROR (LSB)
+FS ERROR (LSB)
-1
Figure 19. +FS Error vs RSOURCE at REF+ or REF- (Small CIN)
0 CREF = 0.01F 6
+FS ERROR (LSB)
-FS ERROR (LSB)
11 VCC = 5V REF + = 5V REF - = GND IN + = 3.75V IN - = 1.25V FO = GND TA = 25C
CREF = 0.1F
17
22
CREF = 1F, 10F 0 0 100 200 300 400 500 600 700 800 900 1000 RSOURCE ()
24361 F22
30
0 100 200 300 400 500 600 700 800 900 1000 RSOURCE ()
24361 F21
Figure 21. +FS Error vs RSOURCE at REF+ and REF- (Large CREF)
U
of the source resistance on the two reference pins is additive with respect to this gain error. The typical +FS and -FS errors for various combinations of source resistance seen by the REF+ and REF- pins and external capacitance CREF connected to these pins are shown in Figures 19, 20, 21 and 22. In addition to this gain error, the converter INL performance is degraded by the reference source impedance. When FO = LOW (internal oscillator and 50Hz/60Hz notch), every 1000 of source resistance driving REF+ or REF- translates into about 1LSB additional INL error. When FO is driven by an external oscillator with a frequency fEOSC, every 100 of source resistance driving REF+ or REF-
3 CREF = 0.01F CREF = 0.001F CREF = 100pF 2 CREF = 0pF VCC = 5V REF + = 5V REF - = GND IN + = GND IN - = 2.5V FO = GND TA = 25C 1 10 100 1k RSOURCE () 10k 100k
2412 F19
W
UU
1
0
Figure 20. -FS Error vs RSOURCE at REF+ or REF- (Small CIN)
30 VCC = 5V REF + = 5V REF - = GND IN + = 1.25V IN - = 3.75V FO = GND TA = 25C
CREF = 1F, 10F
22
17
CREF = 0.1F 11 CREF = 0.01F
6
Figure 22. -FS Error vs RSOURCE at REF+ and REF- (Large CREF)
24361f
23
LTC2436-1
APPLICATIO S I FOR ATIO
translates into about 5.5 * 10-7 * fEOSCLSB additional INL error. Figure 23 shows the typical INL error due to the source resistance driving the REF+ or REF- pins when large CREF values are used. The effect of the source resistance on the two reference pins is additive with respect to this INL error. In general, matching of source impedance for the REF+ and REF- pins does not help the gain or the INL error. The user is thus advised to minimize the combined source impedance driving the REF+ and REF- pins rather than to try to match it. The magnitude of the dynamic reference current depends upon the size of the very stable internal sampling capacitors and upon the accuracy of the converter sampling clock. The accuracy of the internal clock over the entire temperature and power supply range is typical better than 0.5%. Such a specification can also be easily achieved by an external clock. When relatively stable resistors (50ppm/C) are used for the external source impedance seen by REF+ and REF-, the expected drift of the dynamic current gain error will be insignificant (about 1% of its value over the entire temperature and voltage range). Even for the most stringent applications a one-time calibration operation may be sufficient.
1 RSOURCE = 1000
INL (LSB)
0
-1 -0.5 -0.4-0.3-0.2-0.1 0 0.1 0.2 0.3 0.4 0.5 VINDIF/VREFDIF VCC = 5V FO = GND REF+ = 5V CREF = 10F TA = 25C REF- = GND 24361 F23 VINCM = 0.5 * (IN + + IN -) = 2.5V
Figure 23. INL vs Differential Input Voltage (VIN = IN+ - IN-) and Reference Source Resistance (RSOURCE at REF+ and REF- for Large CREF Values (CREF 1F)
24
U
In addition to the reference sampling charge, the reference pins ESD protection diodes have a temperature dependent leakage current. This leakage current, nominally 1nA (10nA max), results in a small gain error. A 100 source resistance will create a 0.05V typical and 0.5V maximum full-scale error. Output Data Rate When using its internal oscillator, the LTC2436-1 can produce up to 6.8 readings per second. The actual output data rate will depend upon the length of the sleep and data output phases which are controlled by the user and which can be made insignificantly short. When operated with an external conversion clock (FO connected to an external oscillator), the LTC2436-1 output data rate can be increased as desired. The duration of the conversion phase is 20510/fEOSC. If fEOSC = 139,800Hz, the converter behaves as if the internal oscillator is used with simultaneous 50Hz/60Hz. There is no significant difference in the LTC2436-1 performance between these two operation modes. An increase in fEOSC over the nominal 139,800Hz will translate into a proportional increase in the maximum output data rate. This substantial advantage is nevertheless accompanied by three potential effects, which must be carefully considered. First, a change in fEOSC will result in a proportional change in the internal notch position and in a reduction of the converter differential mode rejection at the power line frequency. In many applications, the subsequent performance degradation can be substantially reduced by relying upon the LTC2436-1's exceptional common mode rejection and by carefully eliminating common mode to differential mode conversion sources in the input circuit. The user should avoid single-ended input filters and should maintain a very high degree of matching and symmetry in the circuits driving the IN+ and IN- pins. Second, the increase in clock frequency will increase proportionally the amount of sampling charge transferred through the input and the reference pins. If large external
24361f
W
UU
LTC2436-1
APPLICATIO S I FOR ATIO
input and/or reference capacitors (CIN, CREF) are used, the previous section provides formulae for evaluating the effect of the source resistance upon the converter performance for any value of fEOSC. If small external input and/ or reference capacitors (CIN, CREF) are used, the effect of the external source resistance upon the LTC2436-1 typical performance can be inferred from Figures 14, 15, 19 and 20 in which the horizontal axis is scaled by 139,800/fEOSC.
30 VCC = 5V REF + = 5V REF - = GND VINCM = 2.5V VIN = 0V FO = EXTERNAL OSCILLATOR
OFFSET ERROR (LSB)
+FS ERROR (LSB)
15 TA = 85C
TA = 25C
0 0 10 20 30 40 50 60 70 80 90 100 OUTPUT DATA RATE (READINGS/SEC)
24361 F24
Figure 24. Offset Error vs Output Data Rate and Temperature
0 60 TA = 85C TA = 25C
RESOLUTION (BITS)
-FS ERROR (LSB)
120 180 240 300 360 420
VCC = 5V REF + = 5V REF - = GND IN + = 1.25V IN - = 3.75V FO = EXTERNAL OSCILLATOR 0 10 20 30 40 50 60 70 80 90 100 OUTPUT DATA RATE (READINGS/SEC)
24361 F26
Figure 26. -FS Error vs Output Data Rate and Temperature
U
Third, an increase in the frequency of the external oscillator above 460800Hz (a more than 3x increase in the output data rate) will start to decrease the effectiveness of the internal autocalibration circuits. This will result in a progressive degradation in the converter accuracy and linearity. Typical measured performance curves for output data rates up to 100 readings per second are shown in Figures 24, 25, 26, 27, 28 and 29. In order to obtain the
420 360 300 240 180 TA = 85C 120 TA = 25C 60 0 VCC = 5V REF + = 5V REF - = GND IN + = 3.75V IN - = 1.25V FO = EXTERNAL OSCILLATOR 0 10 20 30 40 50 60 70 80 90 100 OUTPUT DATA RATE (READINGS/SEC)
24361 F25
W
UU
Figure 25. +FS Error vs Output Data Rate and Temperature
17
16 TA = 25C 15 TA = 85C VCC = 5V + = 5V REF REF - = GND VINCM = 2.5V VIN = 0V FO = EXTERNAL OSCILLATOR RESOLUTION = LOG2(VREF/NOISERMS) 0 10 20 30 40 50 60 70 80 90 100 OUTPUT DATA RATE (READINGS/SEC)
24361 F27
14
13
12
Figure 27. Resolution (NoiseRMS 1LSB) vs Output Data Rate and Temperature
24361f
25
LTC2436-1
APPLICATIO S I FOR ATIO
18 16 RESOLUTION (BITS) TA = 85C 14 VCC = 5V REF + = 5V REF - = GND VINCM = 2.5V -2.5V < VIN < 2.5V FO = EXTERNAL OSCILLATOR RESOLUTION = LOG2(VREF/INLMAX) 0 10 20 30 40 50 60 70 80 90 100 OUTPUT DATA RATE (READINGS/SEC)
24361 F28
OFFSET ERROR (LSB)
TA = 25C
12
10
8
Figure 28. Resolution (INLMAX 1LSB) vs Output Data Rate and Temperature
highest possible level of accuracy from this converter at output data rates above 20 readings per second, the user is advised to maximize the power supply voltage used and to limit the maximum ambient operating temperature. In certain circumstances, a reduction of the differential reference voltage may be beneficial. Increasing Input Resolution by Reducing Reference Voltage The resolution of the LTC2436-1 can be increased by reducing the reference voltage. It is often necessary to amplify low level signals to increase the voltage resolution of ADCs that cannot operate with a low reference voltage. The LTC2436-1 can be used with reference voltages as low as 100mV, corresponding to a 50mV input range with full 16-bit resolution. Reducing the reference voltage is functionally equivalent to amplifying the input signal, however no amplifier is required. The LTC2436-1 has a 76V LSB when used with a 5V reference, however the thermal noise of the inputs is 800nVRMS and is independent of reference voltage. Thus reducing the reference voltage will increase the resolution at the inputs as long as the LSB voltage is significantly larger than 800nVRMS. A 325mV reference corresponds to a 5V LSB, which is approximately the peak-to-peak value of the 800nVRMS input thermal noise. At this point, the
26
U
16 VCC = 5V REF + = GND VINCM = 2.5V VIN = 0V FO = EXTERNAL OSCILLATOR TA = 25C 8 VREF = 5V VREF = 2.5V 0 0 10 20 30 40 50 60 70 80 90 100 OUTPUT DATA RATE (READINGS/SEC)
24361 F29
W
UU
Figure 29. Offset Error vs Output Data Rate and Reference Voltage
output code will be stable to 1LSB for a fixed input. As the reference is decreased further, the measured noise will approach 800nVRMS. Figure 30 shows two methods of dividing down the reference voltage to the LTC2436-1. Where absolute accuracy is required, a precision divider such as the Vishay MPM series dividers in a SOT-23 package may be used. A 51:1 divider provides a 98mV reference to the LTC24361 from a 5V source. The resulting 49mV input range and 1.5V LSB is suitable for thermocouple and 10mV fullscale strain gauge measurements. If high initial accuracy is not critical, a standard 2% resistor array such as the Panasonic EXB series may be used. Single package resistor arrays provide better temperature stability than discrete resistors. An array of eight resistors can be configured as shown to provide a 294mV reference to the LTC2436-1 from a 5V source. The fully differential property of the LTC2436-1 reference terminals allow the reference voltage to be taken from four central resistors in the network connected in parallel, minimizing drift in the presence of thermal gradients. This is an ideal reference for medium accuracy sensors such as silicon micromachined pressure and force sensors. These devices typically have accuracies on the order of 2% and fullscale outputs of 50mV to 200mV.
24361f
LTC2436-1
PACKAGE DESCRIPTIO
.254 MIN
.0165 .0015
RECOMMENDED SOLDER PAD LAYOUT 1 .015 .004 x 45 (0.38 0.10) .007 - .0098 (0.178 - 0.249) .016 - .050 (0.406 - 1.270) NOTE: 1. CONTROLLING DIMENSION: INCHES INCHES 2. DIMENSIONS ARE IN (MILLIMETERS) 3. DRAWING NOT TO SCALE *DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE **DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE 0 - 8 TYP .053 - .068 (1.351 - 1.727) 23 4 56 7 8 .004 - .0098 (0.102 - 0.249)
Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
U
GN Package 16-Lead Plastic SSOP (Narrow .150 Inch)
(Reference LTC DWG # 05-08-1641)
.045 .005 .189 - .196* (4.801 - 4.978) 16 15 14 13 12 11 10 9 .009 (0.229) REF .150 - .165 .229 - .244 (5.817 - 6.198) .150 - .157** (3.810 - 3.988) .0250 TYP .008 - .012 (0.203 - 0.305) .0250 (0.635) BSC
GN16 (SSOP) 0502
24361f
27
LTC2436-1
TYPICAL APPLICATIO
5V 8 x 2k ARRAY REF - VREF = 294mV 147mV INPUT RANGE 4.5V LSB VISHAY MPM1001/5002B 5V 50k REF + 1k REF - VREF = 95.04mV 49mV INPUT RANGE 1.5V LSB 1 2 5V 3 4 HONEYWELL FSL05N2C 500 GRAM FORCE SENSOR
PANASONIC EXB-2HV202G REF + 5V 0.1F 4.7F 14
Figure 30. Increased Resolution Bridge/Temperature Measurement
RELATED PARTS
PART NUMBER LT1019 LTC1043 LTC1050 LT1236A-5 LT1461 LTC2400 LTC2401/LTC2402 LTC2404/LTC2408 LTC2410 LTC2411 LTC2411-1 LTC2412 LTC2413 LTC2414/LTC2418 LTC2415 LTC2420 LTC2424/LTC2428 LTC2440 DESCRIPTION Precision Bandgap Reference, 2.5V, 5V Dual Precision Instrumentation Switched Capacitor Building Block Precision Chopper Stabilized Op Amp Precision Bandgap Reference, 5V Micropower Precision LDO Reference 24-Bit, No Latency ADC in SO-8 1-/2-Channel, 24-Bit, No Latency ADC in MSOP 4-/8-Channel, 24-Bit, No Latency ADC 24-Bit, Fully Differential, No Latency ADC 24-Bit, No Latency ADC in MSOP 24-Bit, Simultaneous 50Hz/60Hz Rejection ADC 2-Channel, 24-Bit, Pin Compatible with LTC2436-1 24-Bit, No Latency ADC 8-/16-Channel, 24-Bit No Latency ADC 24-Bit, No Latency ADC with 15Hz Output Rate 20-Bit, No Latency ADC in SO-8 4-/8-Channel, 20-Bit, No Latency ADCs High Speed, Low Noise 24-Bit ADC COMMENTS 3ppm/C Drift, 0.05% Max Precise Charge, Balanced Switching, Low Power No External Components 5V Offset, 1.6VP-P Noise 0.05% Max, 5ppm/C Drift High Accuracy 0.04% Max, 3ppm/C Max Drift 0.3ppm Noise, 4ppm INL, 10ppm Total Unadjusted Error, 200A 0.6ppm Noise, 4ppm INL, 10ppm Total Unadjusted Error, 200A 0.3ppm Noise, 4ppm INL, 10ppm Total Unadjusted Error, 200A 0.16ppm Noise, 2ppm INL, 3ppm Total Unadjusted Error, 200A 1.45VRMS Noise, 2ppm INL 0.3ppm Noise, 2ppm INL, Pin Compatible with LTC2411 800nV Noise, 2ppm INL, 3ppm TUE, 200A Simultaneous 50Hz/60Hz Rejection, 800nVRMS Noise 0.2ppm Noise, 2ppm INL, 3ppm Total Unadjusted Error, 200A Pin Compatible with the LTC2410 1.2ppm Noise, 8ppm INL, Pin Compatible with LTC2400 1.2ppm Noise, 8ppm INL, Pin Compatible with LTC2404/LTC2408 4kHz Output Rate, 200nV Noise, 24.6 ENOBs
24361f
28
Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 q FAX: (408) 434-0507
q
U
VCC REF
+
FO
REF - CH0+ LTC2436-1 CH0- SCK SDO 13 12 11
5
6 THERMOCOUPLE 7 8, 9, 10, 15, 16
CH1+ CH1- GND
CS
24361 F30
LT/TP 0103 2K * PRINTED IN USA
www.linear.com
(c) LINEAR TECHNOLOGY CORPORATION 2003

▲Up To Search▲

Price & Availability of LTC2436-1

	To Download LTC2436-1 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .